Reclaiming Clay: A Rationale and Pictorial How-To

 

The Summer Re-Run Blog Posts are running down. This might be the last one, but it’s a goodie; one where the comments are probably more interesting than the post itself. Originally published September 26, 2012, it speaks to a grown-up awakening regarding resources and costs. And while this is still a great method, I no longer work this way and my clay scraps have been reduced to near ZERO. I will let you have fun reading about this small scale reclaiming method (and be sure to peruse the comments!) and then, in the sign-off, I will tell you what I do now…Enjoy!

 

So, how is it that I didn’t learn this early on in my clay career? And, even curiouser, once I did learn it, why did I not practice it until 2012? It was clearly due to a perfect storm of economics and sloth, involving

• A very handy and dirt-cheap (pun intended!) source for clay

• An all-too-convenient method of dumping all scraps into a group recycling process

•  A strong streak of fastidiously-fed laziness cloaked in an utter lack of interest

I had no compelling reason to deal with my scraps. Being a slow-working hand-builder, I also just don’t create the massive leftovers like those wheel-throwing potters do, therefore I was not especially forced to deal with them. The scraps easily disappeared and all I had to do was open a nice fresh bag of just-right clay instead. It was that way for a decade.

 

In the past year, however, compelling reasons and needs to deal with leftovers have come to town:

• I pay retail for my clay now.

• It’s a hassle to get all those heavy buckets of dried chunks over to the college to feed to their recycle stream, and they take up a lot of room while they wait. (Plus the dog will eat them if left uncovered at his nose level!)

• I got curious about how much more work I could get out of a bag of clay if I did this.

Let’s take a look at what’s involved.

As I work, I toss my scraps into a bucket. When it’s full, I chunk them up into even-ish pieces, as in the photo up top.

Scraps get dunked and bagged.

At the end of a studio day, in preparation for the next morning, I dip those chunks – all ranges of wet to dry  – handful by handful in water for a few seconds and then into an empty clay bag.

 

Wetted scraps sit overnight.

I wrap the bag well and let the scraps absorb the water at least overnight, but they will keep for a long time until I’m ready to reclaim.

The really messy part that I avoided until now.

Usually the clay scraps have turned into a slippery-sticky-lumpy goo. I take this out of the bag and spread it as best as I can on a flat rectangular plaster bat. The plaster is a really absorbent surface which will suck the water out of the clay in a matter of hours, but a piece of drywall or wood could work….even canvas, just change it out if it gets too damp before the clay is workable. (Newspaper or paper towels NOT recommended!)

 

Did I say it was gooey sticky and messy?

 

 

The plaster soaks up the water fairly quickly.

Plaster works great. When the clay pulls away, it’s time to flop it over to the other side for awhile.

 

Gather the now-manageable clay and wedge it.

When both sides aren’t sticky, it’s time to ball up the scraps completely and wedge to create as even a texture as possible, in both wetness and consistency. You can throw the lumpy balls onto your wedging surface to compact and condense even further.

 

Pound it into a thickish slab.

Use your fists or something like this firm-squishy bouncy bonker, and flatten your wedged lumps of clay to pancakes about 2 inches thick.

 

 

Roll the slab thinner.

Then using a slab roller or a rolling pin and gauge sticks, roll the thick slabs into thinner ones. Alternatively, you can skid the thick slab along a surface to thin and stretch it by tossing it slightly sideways.

 

Poke holes in the inevitable air bubbles.

 

Air bubbles aren’t the bane for hand-building that they are for wheel-throwing, but it’s still nice to remove the obvious ones.

 

 

A few fresh new slabs from spare parts.

 

Continue to roll out as thin as you need for your project. I always feel rich to get this much more usable clay out of a bucket of scraps.

And that’s the easy illustrated why and how of getting the most out of your bag of clay! Do it and revel in your own bumper crop.

~Liz Crain, who now pretty much uses ALL of her clay the first time around by keeping scraps workably moist and then either generating all sorts of rolled, textured and cut test tiles and tubes which she bisques and keeps on hand for quicker answers to surface design/glazing possibilities AND/OR she forms the wet pieces back into small balls and makes lovely spontaneous pinched pieces, some of which are keepers, the rest are also testing candidates.

Share this: